
Short answer
A graft storage solution is the liquid in which follicular units harvested by FUE wait until they are implanted; its job is to keep grafts from drying out, warming up or being damaged mechanically. The options most clinics use are normal saline (0.9% NaCl) and Ringer's lactate; some centres prefer hypothermic storage solutions developed for cell preservation. The routine matters as much as the solution: grafts are kept moist in solution in glass petri dishes on a tray cooled to about 4–8 °C, sorted and counted by hair number, and their time out of the body is kept short. Which solution and protocol are used is the physician's decision; this article covers only the supplies and the workflow.
What affects graft viability?
From the moment a graft leaves the body until it is placed in its incision, it waits without a blood supply. Graft viability during that wait is protected against four factors:
| Risk | What happens | Supply-side measure |
|---|---|---|
| Drying (dehydration) | The graft surface dries quickly, and dried cells do not recover | Grafts kept in solution, lidded petri dishes, regular moistening |
| Warming | Room and lamp heat raise the cells' energy demand | Cooled tray, cold holding at 4–8 °C, placed away from the lamp |
| Mechanical damage | Squeezing with forceps, gripping the bulb, crushing | Fine-tipped sorting and implantation forceps, gripping the surrounding tissue |
| Long waiting time | Risk rises the longer grafts stay out of the body | Matching the pace of extraction, sorting and implantation; working in counted batches |
Three of these four factors are purely a matter of supplies and organisation: the right dish, the right temperature, the right forceps and a well-planned team flow.
Types of graft storage solution
Clinics generally use one of three groups of solution. The table summarises the differences; the choice and protocol belong to the physician.
| Solution | Composition | Key feature | Note |
|---|---|---|---|
| Normal saline (0.9% NaCl) | Isotonic salt water | Common, easy to source, economical | The standard holding liquid in many clinics |
| Ringer's lactate | Electrolytes + lactate | Electrolyte balance closer to plasma | Used as an alternative to saline |
| Hypothermic storage solutions | Buffers and protective components formulated for cold storage | Designed to protect cells at low temperature | Some centres prefer them for longer procedures |
Some clinics follow protocols that add ATP or similar additives to the holding liquid; these depend on the physician's assessment and are not a standard requirement. Whatever liquid is chosen, three rules stay the same: it must be sterile, within its expiry date, and once opened used only for that procedure.
Cold holding: 4–8 °C and the cold chain
In graft storage, temperature is as decisive as the solution. In practice the petri dishes holding the grafts sit on a tray cooled with ice or a cooling unit, at roughly 4–8 °C. Points to watch:
- Grafts must not freeze; ice never touches the grafts or the solution directly and stays beneath the petri dish.
- Solution bottles are kept in the refrigerator before the procedure; the amount needed is poured into a sterile gallipot or petri dish.
- The cooling tray is not placed directly under the surgical lamp; heat and light speed up drying.
- In long procedures the ice or coolant is replaced regularly and the temperature is checked with a thermometer.

Solutions
Saline, Ringer's lactate and hypothermic solution
Petri dishes, counting trays and the sorting table
In most clinics grafts wait in a borosilicate glass petri dish: it is reusable, autoclavable and transparent, so grafts are easy to see under loupes or a microscope. Small dishes keep single, double and triple groups apart; large dishes are used for bulk holding. For counting, a gridded template can be placed under the dish, or grafts are laid out in rows of ten.
The sorting table should be lit, flat and easy to clean. It should hold, at the same time: the cooled tray, petri dishes, a solution gallipot, sorting forceps, loupes or a microscope, sterile swabs and the count sheet.
Sorting and arranging grafts by hair count
The sorting team separates harvested grafts by hair count: single-hair grafts are usually planned for the frontal hairline, two- and three-hair grafts for the mid and rear areas. While sorting:
- Grafts are held by the surrounding tissue, not the bulb, using fine, precise sorting forceps.
- Each group is kept in its own petri dish or a separate section of the same dish.
- Each dish is labelled with group and count; the count sheet is updated throughout the procedure.
- Grafts go to the implantation team in small batches, so each batch spends only a short time out of the body.
For forceps types and tip choice, see our hair transplant forceps types guide.

Cold holding
Petri dishes, cooled tray and sorting table
Team workflow: pacing extraction, sorting and implantation
The most effective way to shorten the time grafts spend out of the body is to match the pace of extraction and implantation. A typical routine:
| Stage | Who | Supplies | Checkpoint |
|---|---|---|---|
| Extraction | Physician + extraction team | FUE punch, micromotor, extraction forceps | Grafts go into solution immediately |
| Sorting and counting | Sorting team | Petri dishes, cooled tray, sorting forceps, loupes | Separated into groups and entered on the count sheet |
| Incisions | Physician | Sapphire blade / slit blade, blade handle | Incision count matched to graft count |
| Implantation | Implantation team | Implantation forceps or DHI implanter pen | Grafts taken in small batches |
This table is a general example; the order and overlap of stages vary with the clinic's technique (FUE, DHI, combined) and the physician's protocol.
Clinic checklist for graft storage
Before the procedure, make sure the following are ready:
- Is the chosen storage solution (saline, Ringer's lactate or a hypothermic solution) available in sufficient quantity, sterile and in date?
- Has the solution been chilled before the procedure; is the ice or cooling unit ready?
- Are there enough glass petri dishes (small and large) and have they been sterilised?
- Are the cooling tray, sterile gallipot and steel tray on the instrument table?
- Are there enough sorting, extraction and implantation forceps (2–3 sets) to cover the sterilisation cycle?
- Are the loupes or microscope and the lit sorting table working?
- Are 10 ml syringes for drawing and moistening, sterile swabs and gloves ready?
- Have the count sheet and dish labels been prepared?

Workflow
Sorting by hair count and implanting in batches
What to check when buying
- Solution: sterile, ÜTS-registered and with several months to expiry; planned by the case according to monthly procedure numbers.
- Petri dishes: borosilicate glass, autoclavable, lidded; in two diameters and in numbers that cover the sterilisation cycle.
- Forceps: stainless steel with fine, aligned tips; separate sorting, extraction and implantation forceps.
- Ancillary supplies: steel trays, gallipots, syringes, swabs and gloves added to the same quotation.
- Lot tracking: the lot number and expiry date of the solution and sterile consumables should appear on the delivery note.
Products
For graft preparation and holding we list the glass petri dish, sorting forceps, extraction forceps, implantation forceps, steel tray and stainless steel gallipot; the 10 ml syringe for drawing solution and the IV set can be added to the same quotation. The categories are hair transplant, hair transplant forceps, surgical instruments and syringes. For the full instrument list see the instruments used in hair transplantation and hair transplant clinic equipment checklist guides, and hair transplant supplies for the whole catalogue; send your list through a quote request.


